HCC 2022 Day 06 🎃 Halloween Witch Gnome

This adorable little female witch gnome perfectly matches the wizard gnome from yesterday. They make a lovely pair!

She is flying on her broomstick and has a little bat and a pumpkin nestled in among the folds of her hat.

Find out how to make her in this tutorial…

Materials supply list

Here is a list of the materials that I used to make this project.

Please note that some of the links included in this article are affiliate links, which means that if you click through and make a purchase I may receive a commission (at no additional cost to you). You can read my full disclosure at the bottom of the page.

• Cricut machine
• Light blue Cricut cutting mat
• Coloured Card (I use 160-240gsm weight of card)
• Collall All Purpose Glue
• Needle Tip Applicator Bottle
• 3D foam pads

Video tutorial

Watch the video below to see how to make this project. Keep scrolling for a written tutorial.

Written tutorial (with photos!)

Here’s how to make your very own Halloween gnome papercraft project using a Cricut machine!

Step 1) Download the cutting file(s) & unzip the downloaded folder

Before you upload the SVG to Design Space, you need to unzip the download folder that it comes in.

• How to unzip a folder on Windows computer
• How to unzip a folder on a Mac
• How to unzip a folder on an iPad/iPhone
• How to unzip a folder on an Android device

Step 2) Upload the SVG file into Design Space

Open up Cricut Design Space and start a new Project.

Click “Upload” and then find your unzipped version of the downloaded files for this project.

Go into the “Cut Files” subfolder and then select the file called SVG_Halloween_Gnome_Female_CraftWithSarah.svg

This is how it should look after you have uploaded the file:

All the layers should appear “on top of each other” as per the image above. If you see all the layers next to each other instead, that means you’ve accidentally uploaded the wrong file type. If that’s the case, click “Cancel” on the bottom-right of the screen and try again.

Make sure you upload the file which starts SVG_ in the filename!!

After uploading, the design will show in your “Recently Uploaded Images”.

Click on it and then press “Add to Canvas” to put it onto your Project.

Click the design on your canvas and use the width/height boxes near the top of the screen to make it the size that you want to cut it.

TIP: Make sure the padlock icon above the width/height boxes is CLOSED before you resize. If it appears “open”, click it with your mouse to close it.

I cut my design at 7.75 inches wide. I don’t recommend going smaller than about 5.5 inches in width as some of the cuts will get a little bit too tiny and hard to stick.

Step 3) Cut out all the layers

When you’re happy with how the project looking in Design Space, click “Make It” and follow the instructions on-screen to cut out all the layers.

To change the paper size, go into the dropdowns over on the left side of the screen and choose the paper size that you want to use. You need to change it for every single colour.

To save space on your cardstock, you can move things around by clicking and dragging. Make sure when you’re moving things about that nothing overlaps because otherwise, it won’t cut out properly.

TIP: New to cutting cardstock with a Cricut? Check out this in-depth tutorial which goes through every step of the process, including tips for getting the best quality cuts from your Cricut.

Step 4) Stick the project together

Use 3D foam pads and glue to stick the layers together.

Use this guide to see the order to stick the layers together in.

A high-quality, un-watermarked printable version of this assembly guide is included in the folder when you download the cut file.

My favourite glue to use on papercraft projects is Collall All Purpose Glue.

It’s SO good because it doesn’t “warp” or bend the cardstock like some glues do. You can use as much of it as you want and the card stays perfect – and it dries perfectly clear too!

To make it even easier to apply glue to layered card projects, I highly recommend getting some of these needle tip applicator bottles to put the glue into.

The nozzles are REALLY tiny which makes them perfect for putting glue in the pieces of cardstock that make up this design.

The foam pads that I use are from “Dot & Dab”, but any foam squares will work. If yours are big then you may need to cut them smaller with scissors to fit inside the edges of the layers.

When adding the foam pads to the relevant layers, make sure you add some in the middle of the pieces of card so it give stability to the middles. If you don’t add any foam pads in the middles then it can “sag” under the weight of the other layers which doesn’t look as good.

Halloween gnome layered papercraft

After sticking all the pieces of card together, you’ll have a wonderful layered Halloween project all ready to be framed.

You could also put her on a greetings card or even stick it straight to the wall with some blu-tack or command strips, or prop it up on a shelf.

The below video has some tips on how to frame your craft project, including my Number One hack for making sure that your design will fit perfectly every time without wasting any of your craft materials.

Happy crafting,
Sarah x