FCC 2024 Day 06: Orchid Layered Design

Step 2) Modify the design if required

There are some customisations you can make to the design to change how it looks.

For example, you could remove the mandala background so that you just cut the flower.

To do that, open up the layers panel by clicking the little arrow next to the design name.

Then, scroll down to the bottom of the layers panel. Click the very bottom layer and either hide it by clicking the eye icon that appears when you hover, or click the trash can icon.

Do the same for the mandala detail layer above.

You’ll then end up with this:

You could also recolour the orchid. To do that, click each of the flower petal layers, one-at-a-time and change them in the colour picker.

Here’s how it could look with a white and yellow orchid instead of pink:

Step 3) Size the orchid design

Click the design on your canvas and use the width/height boxes near the top of the screen to make it the size that you want to cut.

TIP: Make sure the padlock icon above the width/height boxes is CLOSED before you resize. If it appears “open”, click it with your mouse to close it.

I don’t recommend going smaller than 4 inches tall as some of the details will get hard to cut. Here’s a tutorial on how to cut designs really small with a Cricut.

If you are cutting this design on the original Cricut Joy machine, you’ll need to make it maximum of 4.5 inches wide.

If you are cutting the design to fit in a specific frame, watch this video to see my top tips on how to resize it to fit perfectly, or read the tutorial here.

Here’s how my orchid design looks after I have followed the steps in the above video to add some square layers behind it.

The outer square measures 9.85 inches square which is the size of my shadow box frame.

The blue square is 8.25 inches wide and the middle square is 8 inches.

The orchid design measures 6.033 inches wide and 7.15 inches tall.

Step 3) Cut out all the layers

When you’re happy with how the project is looking in Design Space, click “Make” and follow the instructions on-screen to cut out all the pieces.

To change the paper size, go into the dropdowns over on the left side of the screen and choose the paper size that you want to use. You need to change it for every single colour.

To save space on your cardstock, you can move things around by clicking and dragging. Make sure when you’re moving things about that nothing overlaps because otherwise, it won’t cut out properly.

TIP: New to cutting cardstock with a Cricut? Check out this in-depth tutorial which goes through every step of the process, including tips for getting the best quality cuts from your Cricut.

Step 4) Stick the project together

Use 3D foam pads and glue to stick the layers together.

Use this guide to see the order to stick the layers together in.

A printable version of this assembly guide is included in the folder when you download the cut files.

My favourite glues to use on papercraft projects are Bearly Art Glue and Collall All Purpose Glue.

These are great because they don’t “warp” or bend the cardstock like some glues do. You can use as much of it as you want and the card stays perfect – and it dries perfectly clear too!

Bearly Art Glue comes with a tiny nozzle to make it easy to apply glue to small areas of card. The Collall glue doesn’t come with this, so it’s easiest to decant it into needle tip applicator bottles so that you have more control.

The foam pads that I use are from “Dot & Dab”, but any foam squares will work. If yours are big then you may need to cut them smaller with scissors to fit inside the edges of the layers.

When adding the foam pads to larger pieces of card, make sure you add some in the middles of the pieces of card so it gives stability to the middles.

If you don’t add any foam pads in the middles then it can “sag” under the weight of the other layers which doesn’t look as good.

Continue sticking the pieces together, following the assembly guide, until your papercraft is all finished.

Orchid layered papercraft design

After sticking all the pieces of card together, you’ll have a lovely orchid papercraft all finished!

I glued my orchid to the square layers that I cut out for the frame, then put it into my shadow box to end up with the finish artwork.

If you’d rather not mount your project in a shadow box, check out these free easel stands for two alternative ways to display it.

Or, go for a more simplistic approach by making a triangle stand or nail hook.

The triangle stands are completely invisible from the from of the project, making it look like it’s standing up by magic! The hooks allow you to hang the design straight on the wall without a frame.

Happy crafting,
Sarah x