HCC 2023 Day 01 🦇 Trick or Treat Teddy Bears

Let’s kick off the Halloween Craft Countdown for 2023 with these adorable little teddy bears.

Both the male and female versions of the teddies are included and they are all dressed up ready to go Trick or Treating!

If you’re new to making papercrafts with your Cricut, especially this type of layered design, these teddies are great designs to get started with as the pieces are fairly simple shapes for the Cricut to cut.

Materials supply list

Here is a list of the materials that I used to make this project.

Please note that some of the links included in this article are affiliate links, which means that if you click through and make a purchase I may receive a commission (at no additional cost to you). You can read my full disclosure at the bottom of the page.

• Cricut machine
• Light blue Cricut cutting mat
• Coloured Card
• Collall All Purpose Glue
• Needle Tip Applicator Bottle
• 3D foam pads

This project is suitable for the following types of Cricut machine: Explore Air 2, Explore Air 3, Maker, Maker 3, Venture and Joy Xtra. You will need to resize the design smaller to use with the original Cricut Joy machine.

Video tutorial

Watch the video below to see how to make this project. Keep scrolling for a written tutorial.

Written tutorial (with photos!)

Here’s how to make your very own Halloween teddy bears using a Cricut machine!

Step 1) Download the cutting file(s) & unzip the downloaded folder

Before you upload the SVG to Design Space, you need to unzip the download folder that it comes in.

• How to unzip a folder on Windows computer
• How to unzip a folder on a Mac
• How to unzip a folder on an iPad/iPhone
• How to unzip a folder on an Android device

Step 2) Upload the SVG file into Design Space

Open up Cricut Design Space and start a new Project.

Click “Upload” and then find your unzipped version of the downloaded files for this project.

The files to upload for Cricut Design Space are the two that starts with svg- in the filename.

Male teddy bear = svg-teddy-halloween-m-craftwithsarah.svg
Female teddy bear = svg-teddy-halloween-f-craftwithsarah.svg

This is how it should look after you have uploaded the file:

All the layers should appear “on top of each other” as per the image above. If you see all the layers next to each other instead, that means you’ve accidentally uploaded the wrong file type. If that’s the case, click “Cancel” on the bottom-right of the screen and try again.

Make sure you upload the file which starts svg- in the filename!!

After uploading, the designs will show in your “Recently Uploaded Images”.

Click on them and then press “Add to Canvas” to put them onto your Project.

Step 3) Simplify the colours (optional)

Some of the colours will load in as very similar but not *quite* the same. To make it easier to cut the teddies so that you need less shades of card, use the “Color Sync” tool at the top of the layers panel.

Click it to sort the layers by colour.

You can see that the black layers on each teddy are different, but very close in colour.

Click-and-drag one group of colour onto another to change it to that colour.

Step 4) Size the teddy bears

Click the designs on your canvas and use the width/height boxes near the top of the screen to make them the size that you want to cut them.

TIP: Make sure the padlock icon above the width/height boxes is CLOSED before you resize. If it appears “open”, click it with your mouse to close it.

I made the male teddy bear 7 inches tall (7.783 inches wide) and the female teddy bear 7.5 inches tall (6.347 inches wide).

These sizes made the teddy bears look “in proportion” with each other, as the female teddy’s witch hat is tall so she needs to be a bit taller than the devil teddy.

I don’t recommend going smaller than about 5 inches tall as some of the cuts will get a little bit too tiny and hard to stick.

If you are cutting the teddies to fit in a specific frame, watch this video to see my top tips on how to resize them to fit perfectly, or read the tutorial here.

Step 5) Cut out all the layers

When you’re happy with how the project looking in Design Space, click “Make It” and follow the instructions on-screen to cut out all the layers.

To change the paper size, go into the dropdowns over on the left side of the screen and choose the paper size that you want to use. You need to change it for every single colour.

To save space on your cardstock, you can move things around by clicking and dragging. Make sure when you’re moving things about that nothing overlaps because otherwise, it won’t cut out properly

TIP: New to cutting cardstock with a Cricut? Check out this in-depth tutorial which goes through every step of the process, including tips for getting the best quality cuts from your Cricut.

Step 6) Stick the project together

Use 3D foam pads and glue to stick the layers together.

Use these guides to see the order to stick the layers together in.

A printable version of this assembly guide is included in the folder when you download the cut files.

My favourite glue to use on papercraft projects is Collall All Purpose Glue.

It’s SO good because it doesn’t “warp” or bend the cardstock like some glues do. You can use as much of it as you want and the card stays perfect – and it dries perfectly clear too!

To make it even easier to apply glue to layered card projects, I highly recommend getting some of these needle tip applicator bottles to put the glue into.

The nozzles are REALLY tiny which makes them perfect for putting glue in the pieces of cardstock that make up this design.

The foam pads that I use are from “Dot & Dab”, but any foam squares will work. If yours are big then you may need to cut them smaller with scissors to fit inside the edges of the layers.

When adding the foam pads to larger pieces of card, make sure you add some in the middle of the pieces of card so it give stability to the middles. If you don’t add any foam pads in the middles then it can “sag” under the weight of the other layers which doesn’t look as good.

Continue sticking the pieces together, following the assembly guides, until your Halloween teddy bears are all finished.

Halloween teddy bear layered papercrafts

After sticking all the pieces of card together, you’ll have two wonderful layered Halloween teddy bears all finished!

You could frame them in a shadow box, put them on a greetings card, use them in your Halloween decorations or displays, or even stick them straight to the wall with some blu-tack or command strips, or prop them up on a shelf.

Check out these free easel stands for a fun way to display them.

Happy crafting,
Sarah x